產品列表 / products
SMC減壓閥選用標準:
標準一 在給定的彈簧壓力級范圍內,使出口壓力在大值與小值之間能連續調整,不得有卡阻和異常振動;
標準二 對于軟密封的減壓閥,在規定的時間內不得有滲漏;對于金屬密封的減壓閥,其滲漏量應不大于大流量的0.5%;
標準三 出口流量變化時,直接作用式的出口壓力偏差值不大于20%,先導式不大于10%;
標準四 進口壓力變化時,直接作用式的出口壓力偏差不大于10%,先導式的不大于5%;
標準五 通常,減壓閥的閥后壓力應小于閥前壓力的0.5倍;
標準六 減壓閥的應用范圍很廣,在蒸汽、壓縮空氣、工業用氣、水、油和許多其他液體介質的設備和管路上均可使用,介質流經減壓閥出口處的量,一般用質量流量或體積流量表示;
標準七 波紋管直接作用式減壓閥適用于低壓、中小口徑的蒸汽介質;
SMC減壓閥維護技巧:
1.為了操作和維護方便,閥門通常安裝在水平管道上。2.減壓閥的安裝必須嚴格按照閥體上箭頭的方向和流體的流向。如果水質含雜質,過濾器必須安裝在減壓閥的上游進口處(我們建議過濾精度不小于0.5mm)。3.為了防止閥門后的壓力過大,應該在閥門的出口處安裝一個壓力安全閥,不小于4M。4.減壓閥在管道中起著一定的作用。為了防止水錘的危害,還可以安裝小型膨脹罐來防止管道和閥門的損壞。過濾器必須安裝在安全閥進水管道之前,并且膨脹罐必須安裝在減壓安全閥出口后。5.如果需要在熱水系統中安裝減壓閥,則必須在減壓閥和膨脹罐之間安裝止回閥。通過這種方式,膨脹罐可以吸收由于熱膨脹而增加的水量,防止熱水回流或壓力波動對減壓閥的影響,從而保證減壓閥的長期正常運行。
上一篇:日本SMC油霧器性能與工作原理