意大利ATOS阿托斯繼電器一般由鐵芯、線圈、銜鐵、觸點huang片等組成的。只要在線圈兩端加上一定的電壓，線圈中就會流過一定的電流，從而產生電磁效應，銜鐵就會在電磁力吸引的作用下克服返回彈簧的拉力吸向鐵芯，從而帶動銜鐵的動觸點與靜觸點（常開觸點）吸合。當線圈斷電后，電磁的吸力也隨之消失，銜鐵就會在彈簧的反作用力返回原來的位置，使動觸點與原來的靜觸點（常閉觸點）釋放。這樣吸合、釋放，從而達到了在電路中的導通、切斷的目的。對于繼電器的“常開、常閉"觸點，可以這樣來區分：繼電器線圈未通電時處于斷開狀態的靜觸點，稱為“常開觸點"；處于接通狀態的靜觸點稱為“常閉觸點"。繼電器一般有兩股電路，為低壓控制電路和高壓工作電路。因為繼電器是由線圈和觸點組兩部分組成的，所以繼電器在電路圖中的圖形符號也包括兩部分.

ATOS壓力繼電器的使用注意事項：

(1)根據具體用途和系統壓力選用適當結構形式的壓力繼電器，為了保證壓力繼電器動作靈敏，避免低壓系統選用高壓壓力繼電器。

(2)應按照制造廠的要求，正確安裝壓力繼電器。

(3)按照所要求的電源形式和具體要求對壓力繼電器中的微動開關進行接線。

(4)壓力繼電器調整完畢后，應鎖定或固定其位置．以免受振動后變動。

(5)壓力繼電器的泄油腔應直接接回油箱，否則會使泄油口背壓過高，影響其靈敏度。

MAP-08020

MAP40/H14

MAP80/K11

MAP-16020

MAP-160/20

MAP-160/E20

MAP-32020

MAP-320/20

MAP-320/E

MAP-630

MAP-630/E20

MAP160/H14

MAP-040/20

MAP-080/20

MAP-160 

MAP-160/E 20

MAP-320/20